Visit Website Press Release. Our Sustainability Commitment is designed around. Ingersoll-Rand Air Compressor Manual. Pages: With our integral gear drive system, hour coolant, and leak-free design you can count on the SSR for years to come. If your business demands any of these then check out the SSR. Industrial Compressor Supplies is not associated with any of the manufacturers listed on our website. Free shipping for many products! Therefore Ingersoll Rand cannot be held responsible for equipment in which non-approved repair parts are installed.
UP6 30E—HA. UP6 40—HA. SSR M ingersoll-rand. Ingersoll Rand Air Compressor Parts. Compressed air should not be used for breathing air applications unless treated in accordance with all applicable codes and regulations. Description Item Qty. Page 10 Lifting equipment must be properly rated for the weight of the used in mineral oils. Ingersoll Rand recommends that only lters with compressor. Page Safety As waste water regulations vary by country and region it is the responsibility of the user to establish the limitations and regulations in their particular area.
Ingersoll Rand and its associated distributors are happy to advise and assist in these matters. Page General Information Contactor main Dashed lines represent wiring by customer. Contactor delta Sizing of electrical components not supplied by Ingersoll Rand is Overload, motor starter the responsibility of the customer and should be done in Switch, pressure Page General Information Switch, high air temperature Dashed lines represent wiring by customer.
Contactor main Sizing of electrical components not supplied by Ingersoll Rand is Overload, motor starter the responsibility of the customer and should be done in accordance with the information on the compressor data plate Switch, pressure and local electrical codes.
Prior to running 9. Sizing of electrical components not supplied by Ingersoll Rand is the the unit the shipping bolt must be removed and the belt tension responsibility of the customer and should be done in accordance with checked. Page 18 Their safety can be affected by either synthetic coolants or the additives used in mineral oils. Air Receiver Ingersoll Rand recommends that only filters with metal bowls 3.
Air Dryer should be used on any pressurised system. Pressure gauge Valve, solenoid Load 2. Pressure switch Indicator air filter 3. Tee Nipple 4. Connector Adaptor 5. Combination block Intake valve assembly 6.
Elbow 7. Reducer bushing A. Make visual check of the machine, ensure that all guards secure and that nothing is obstructing the proper ventilation of, or free access WARNING to the machine. DO NOT operate the compressor at discharge pressures exceeding the maximum operating pressure. The compressor will unload and stop. Turn off electrical isolator or disconnect.
Page 27 Clean the interior thoroughly and local or national running with safety protection devices disabled or removed. Page Maintenance National environmental protection codes. Remove the new Ingersoll Rand replacement filter from its protective package. Page 29 4. Clean the mating face of the housing.
Remove the new Ingersoll Rand replacement cartridge from its protective package. Stop the machine, electrically isolate and vent all trapped pressure. Slowly close the isolation valve located adjacent to the compressor. Remove the side cover from the machine. Page Trouble Shooting Fit inlet valve service kit. System demand exceeds compressor delivery. Reduce demand or install additional compressor.
Page Trouble Shooting Safety valve faulty Check the setting of the safety valve and the rated pressure. Page 17 Loosen, remove and discard 10mm shipping bolt. For belt the information on the compressor data plate and national and local tensioning procedure refer to Maintenance section. Page 18 It is a requirement for air dryers covered under Aircare that correctly individual air lines. Page Odp There is a decal fitted to the starter door describing the procedure to change the connections for the alternative voltage Rewiring should only be effected by a competent Electrician.
Page 20 There is a decal fitted to the starter door describing the procedure to change the connections for the alternative voltage Rewiring should only be effected by a competent Electrician. Page 22 An independent electrical isolator or disconnect should be installed Ensure that the motor rotates in the correct direction as adjacent to the compressor.
Lubricants, greases or other items containing silicone should not be used on this unit. Page 24 4. Connector Adaptor 5. Combination block Intake valve assembly 6. Elbow 7. Reducer bushing A. Valve, solenoid Blowdown B. Page Controls 7. Investigate cause of fault. Page 26 2. Turn off electrical isolator or disconnect. Page 27 Remove the cover plate and any necessary running with safety protection devices disabled or removed.
Clean the interior thoroughly and legislation. Page 28 3. Remove plug from drain valve. Open the drain valve and drain coolant into container. Close the drain valve. Replace plug in drain valve. Page Maintenance 6. Apply a small amount of lubricant to the cartridge seal.
0コメント